[2024] Use Valid New ECP-206 Questions - Top choice Help You Gain Success
ECP-206 Exam Practice Materials Collection
NEW QUESTION # 11
Which operating system is used in Ericsson Router 6000 products?
- A. ERS
- B. IPOS
- C. Junos
- D. SE-OS
- E. ERS
Answer: A
Explanation:
Explanation
The operating system used in Ericsson Router 6000 products is ERS (Ericsson Router Software). ERS is based on IPOS (IP Operating System), which is a common operating system for Ericsson's IP portfolio. ERS provides advanced features and functionality for IP transport, such as MPLS, Segment Routing, QoS, IPSec, synchronization, SDN, and more. ERS also supports seamless integration with Ericsson Radio System and Ericsson Network Manager.
References: Router 6000 Series - Ericsson, Router 6675 Datasheet - Winncom
NEW QUESTION # 12
What is the purpose of the RT attribute?
- A. to request BGP neighbors to avoid routing through a private AS
- B. to prevent OSPF routing loops in an L3VPN environment
- C. to indicate an MPLS LSP as the next hop routing target
- D. to identify the destination VPN on the efress PE
Answer: D
Explanation:
Explanation
The purpose of the RT attribute is to identify the destination VPN on the egress PE. RT stands for route target, which is a BGP extended community attribute that is used in MPLS VPNs. RT is attached to VPN routes by the ingress PE router and is used to control the import and export of routes between different VPNs. The egress PE router uses the RT value to determine which VPN routes belong to which VPN customers and installs them in the appropriate VRF table56.
References: IP Routing: BGP Configuration Guide - BGP-RT and VPN ... - Cisco, <rt>: The Ruby Text element - MDN Web Docs
NEW QUESTION # 13
Which mismatched field would cause an IS-IS adjacency between two routers to fail?
- A. SEL
- B. MTU
- C. Context
- D. SysID
Answer: B
Explanation:
Explanation
MTU mismatch would cause an IS-IS adjacency between two routers to fail. MTU stands for maximum transmission unit, which is the maximum size of a packet that can be transmitted on a link. IS-IS hellos are padded to the full MTU size, partly to allow a router to implicitly communicate its MTU to its neighbors. If two routers have different MTUs on their interfaces, they will not be able to exchange hellos properly, and their adjacency will not form or will be dropped34. To solve this problem, the MTUs on both interfaces must be configured to match.
SEL, context, and SysID are not fields that would cause an IS-IS adjacency failure. SEL stands for selector, which is a one-octet field that identifies the network layer service to which a packet should be sent. For IS-IS routers, the SEL must always be 005. Context is not a field in IS-IS packets, but rather a term used to describe the scope of routing information in different levels or areas6. SysID stands for system identifier, which is a six-octet field that uniquely identifies a router within an area. SysID does not have to match between two routers for them to form an adjacency7.
References: MTU Mismatch Problem in IS-IS - Cisco, IS-IS adjacency is not formed due to MTU mismatch - Cisco Community, IS-IS NSAP address - Cisco Community, Understanding IS-IS Routing Contexts - Juniper Networks, IS-IS - Nokia
NEW QUESTION # 14
Which conceptual table created by routing protocols is used when processing an IP packet?
- A. label information base
- B. forwarding information base
- C. management information base
- D. traffic engineering data base
Answer: B
Explanation:
Explanation
The conceptual table created by routing protocols that is used when processing an IP packet is the forwarding information base (FIB). The FIB is a table that contains the bestroutes to reach each destination network prefix, along with the outgoing interface and the next-hop address for each route. The FIB is derived from the routing information base (RIB), which is a table that contains all the routes learned from different routing protocols and sources. The FIB is used by the router to make fast forwarding decisions for each incoming packet, based on its destination address12.
References: Security Hardening Checklist Guide for Cisco Routers/Switches in 10 Steps, VLAN - Wikipedia
NEW QUESTION # 15
What is a label-edged router (LER)?
- A. a DR router
- B. a CE router
- C. a P router
- D. a PE router
Answer: D
Explanation:
Explanation
A label-edged router (LER) is a PE router. A PE router is a provider edge router, which is a router that connects an MPLS network to a customer network. A LER is a term used in MPLS to describe a router that resides at the ingress and egress points of an MPLS network, handling both labelled and unlabelled packets. A LER performs label operations such as adding, removing, or swapping labels on packets entering or leaving the MPLS network34.
References: What is Label Edge Router (LER)? - Definition from Techopedia, LER - Label Edge Router - Mpirical
NEW QUESTION # 16
Which two features does IPsec provide? (Choose two.)
- A. controlling the path through the network
- B. hiding the content of packets from observation
- C. protecting the length of packets from discovery
- D. protecting packets from modification
Answer: B,D
Explanation:
Explanation
IPsec provides two main features: protecting packets from modification and hiding the content of packets from observation. IPsec protects packets from modification by using cryptographic algorithms to generate and verify message authentication codes (MACs) or digital signatures for each packet. These mechanisms ensure that the packets have not been tampered with or altered in transit by unauthorized parties. IPsec hides the content of packets from observation by using encryption algorithms to scramble the payload of each packet. This prevents eavesdroppers or interceptors from reading or analyzing the data carried by the packets12.
References: What is IPsec? | How IPsec VPNs work | Cloudflare, IPsec - Wikipedia
NEW QUESTION # 17
What is the correct abbreviation for the IP address: BFEA:DACA:0000:0000:9390:0000:0000:D91?
- A. BFEA:DACA::9390:0:0:D91
- B. BFEA:DACA::9390::D91
- C. BFEA:DACA::D91/6
- D. BFEA:DACA::9390:0:D91
Answer: D
Explanation:
Explanation
The correct abbreviation for the IP address BFEA:DACA:0000:0000:9390:0000:0000:D91 is BFEA:DACA::9390:0:D91. IPv6 addresses are represented in hexadecimal notation, with eight 16-bit segments separated by colons. To simplify the address representation, IPv6 supports two types of abbreviations. The first abbreviation allows us to skip leading zeros within a segment, while the second abbreviation allows us to drop one or more consecutive segments that contain only zeros, using a double colon (::) instead. However, the double colon can be used only once in an address, to avoid ambiguity34.
References: IPv6 Address Types, Notation, and Structure Explained, IPv6 address - Wikipedia
NEW QUESTION # 18
Which statement is true about LDP?
- A. LDP and IGP both exchange their databases every 30 seconds.
- B. LDP relies on IGP for all routing-related decisions.
- C. LDP and IGP both exchange their databases every 60 seconds.
- D. LDP performs routing functions along with IGP.
Answer: B
Explanation:
Explanation
LDP relies on IGP for all routing-related decisions. LDP is a protocol that distributes labels in an MPLS environment, but it does not perform any routing functions. LDP uses the underlying routing information provided by an IGP, such as OSPF or IS-IS, to forward label packets. LDP and IGP do not exchange their databases at regular intervals, but rather use hello messages to maintain adjacencies and sessions. References: Ericsson IP Networking - Routing Protocols, Label Distribution Protocol - Wikipedia
NEW QUESTION # 19
Which two statements are true about the Ericsson Router 6000 series? (Choose two.)
- A. The Router 6000 uses the same building practice and accessories as the Ericsson Radio System.
- B. The Router 6000 can host containerized applications such as firewalls.
- C. The Router 6000 products range from all-outdoor small site routers to large aggregation routers.
- D. The Router 6000 is solely built as a radio cell site router.
Answer: A,C
Explanation:
Explanation
Two statements that are true about the Ericsson Router 6000 series are:
The Router 6000 uses the same building practice and accessories as the Ericsson Radio System. The Ericsson Radio System is a modular and scalableradio access network solution that supports multiple standards, bands, and layers. The Router 6000 series is fully integrated into the Ericsson Radio System, using the same building practice and accessories such as mounting kits, cables, power supplies, etc. This simplifies installation, operation, and maintenance of both radio and transport equipment78.
The Router 6000 products range from all-outdoor small site routers to large aggregation routers. The Router 6000 series consists of three main products: the Router 6672 for access, the Router 6675 for pre-aggregation, and the Router 6274 for metro aggregation. The Router 6672 is an all-outdoor small cell site router with high-capacity and low-power consumption. The Router 6675 is a combined access and E-RAN switch with hardware-accelerated IPSec and high-accuracy internal clock. The Router 6274 is a high-capacity metro aggregation router with SDN functionality and flexible interface options78.
References: Router 6000 Series - Ericsson, New Ericsson Router 6000 series couples radio and IP transport for 5G future - Global Brands Magazine
NEW QUESTION # 20
Which two protocols apply to both IPv4 and IPv6? (Choose two.)
- A. ARP
- B. SNMP
- C. MD
- D. DNS
Answer: B,D
Explanation:
Explanation
Two protocols that apply to both IPv4 and IPv6 are:
SNMP: This stands for Simple Network Management Protocol, which is a protocol that allows network administrators to monitor and manage network devices such as routers, switches, servers, printers, etc.
SNMP uses a client-server model, where an SNMP manager (client) can query or configure an SNMP agent (server) on a network device using SNMP messages. SNMP can operate over both IPv4 and IPv6 networks56.
DNS: This stands for Domain Name System, which is a protocol that translates human-readable domain names (such as www.example.com) into numerical IPaddresses (such as 192.0.2.1 or 2001:db8::1) that identify network devices. DNS uses a hierarchical distributed database of name servers that store and resolve domain names and IP addresses. DNS can support both IPv4 and IPv6 addresses78.
References: Simple Network Management Protocol - Wikipedia, SNMP over IPv6 - Cisco, Domain Name System - Wikipedia, DNS for IPv6 - Cisco
NEW QUESTION # 21
In OSPFv2, which route characteristic is used to determine the best path?
- A. delay
- B. jitter
- C. cost
- D. packet loss
Answer: C
Explanation:
Explanation
In OSPFv2, the route characteristic that is used to determine the best path is the cost. The cost is a metric that represents the link bandwidth, delay, reliability, or other factors. The cost is inversely proportional to the bandwidth, meaning that a higher bandwidth link has a lower cost. The cost of a route is calculated by adding the costs of all links along the path. OSPFv2 uses the following formula to calculate the cost of an interface:
Cost = Reference bandwidth / Interface bandwidth in bps
The reference bandwidth is a constant value that can be configured by the network administrator. By default, it is 100 Mbps. The interface bandwidth is the actual bandwidth of the interface in bits per second. For example, if an interface has a bandwidth of 10 Mbps, its cost would be 100 Mbps / 10 Mbps = 101415.
OSPFv2 does not use jitter, packet loss, or delay as route characteristics to determine the best path. Jitter is the variation in latency or delay between packets. Packet loss is the percentage of packets that are dropped or corrupted during transmission. Delay is the time it takes for a packet to travel from source to destination. These characteristics are not part of the OSPFv2 protocol and are not advertised in OSPFv2 LSAs1617.
References: OSPF Metric cost Calculation Formula Explained - ComputerNetworkingNotes, OSPF Cost - OSPF Routing Protocol Metric Explained - Study-CCNA, Open Shortest Path First - Wikipedia, OSPF Metric
= Cost - Cisco
NEW QUESTION # 22
What is a reason for using VLANs in an IP network?
- A. to implement virtual routing
- B. to isolate hosts within the same IP subnet
- C. to enable MAC address learning on a router port
- D. to isolate hosts across multiple IP subnets
Answer: B
Explanation:
Explanation
A reason for using VLANs in an IP network is to isolate hosts within the same IP subnet. VLANs (Virtual LANs) are logical grouping of devices in the same broadcast domain. VLANs are usually configured on switches by placing some interfaces into one broadcast domain and some interfaces into another. Each VLAN acts as a subgroup of the switch ports in an Ethernet LAN. VLANs allow network administrators to group hosts together even if the hosts are not directly connected to the same network switch. By using VLANs, hosts within the same IP subnet can be separated into different broadcast domains, which enhances security, reduces network congestion, and simplifies network management78.
References: 8 Different Types of VLANs in TCP/IP Networks, What is a VLAN? - Study-CCNA
NEW QUESTION # 23
Which two label actions are performed by a P router? (Choose two.)
- A. drop
- B. php
- C. swap
- D. push
Answer: B,C
Explanation:
Explanation
A P router is a provider router that is part of the service provider's core network in an MPLS environment. A P router does not have any customer routes or VPN information, but only has information about how to reach other P routers and PE routers in the same MPLS domain. A P router performs label switching, which means that it forwards labeled packets based on their top label in the label stack. A P router can perform two possible label actions:
Swap: The P router replaces the incoming label with a new label that corresponds to the next hop along the label-switched path (LSP). The new label is determined by looking up the label forwarding information base (LFIB) based on the incoming label and interface.
PHP: The P router removes the top label from the packet at the penultimate hop before reaching the egress PE router. This is done to avoid an extra lookup on the egress PE router, which can forward the packet based on its IP header or another label in the stack.
A P router does not perform push or drop actions on labels. A push action means adding one or more labels to the packet, which is done by an ingress PE router when initiating an LSP. A drop action means discarding a packet, which is done by any router when there is no matching entry in its LFIB or routing table. References: Provider (P) Router in IP MPLS Network - Cisco Community, MPLS Fundamentals: Forwarding Labeled Packets - Cisco Press, MPLS Label Switching | MPLS Operation | Push, Swap,Push IPCisco
NEW QUESTION # 24
How do peers recognize each other's ability to use MP-BGP extensions?
- A. They advertise the ability using the capabilities field in the update packet.
- B. They advertise the ability using the capabilities field in the End-of-RIB marker.
- C. They advertise the ability using the capabilities field during the session establishment.
- D. They advertise the ability using the capabilities field in the hello packet.
Answer: C
Explanation:
Explanation
Peers recognize each other's ability to use MP-BGP extensions by advertising the ability using the capabilities field during the session establishment. MP-BGP is an extension to BGP that allows BGP to carry routing information for multiple network layer protocols, such as IPv6, VPNv4, multicast, etc. To support MP-BGP, peers need to exchange their capabilities during the session establishment phase, which consists of three steps:
open, keepalive, and update. In the open message, peers can include an optional parameter called capabilities, which indicates what kind of address families and subsequent address families they can support. If both peers agree on a common set of capabilities, they can proceed to exchange routing information for those address families using update messages56.
References: Use of MP-BGP Extensions for IPv6 Interdomain Routing, MP-EBGP Configuration Example - Cisco
NEW QUESTION # 25
Which router function advertises external routes in OSPF?
- A. designated router
- B. ABR
- C. backbone router
- D. ASBR
Answer: D
Explanation:
Explanation
The router function that advertises external routes in OSPF is ASBR, which stands for Autonomous System Boundary Router. An ASBR is a router that connects an OSPF domain to another routing domain, such as another OSPF domain or a different routing protocol domain. An ASBR can redistribute routes from other routing domains into OSPF as external routes, which are carried in type 5 or type 7 LSAs. External routes have two types: E1 and E2. E1 routes include the cost from the ASBR to the destination, while E2 routes only include the cost advertised by the ASBR34.
References: OSPF External Routes IpCisco, OSPF External Route selection algorithm - Cisco Community
NEW QUESTION # 26
What network information is, without additional configuration, shared between two iBGP neighbors by default?
- A. BGP routes learned from eBGP neighbors
- B. BGP routes learned from an OSPF neighbor
- C. IP address information of loopback interfaces
- D. IP address information from all directly connected interfaces
Answer: A
Explanation:
Explanation
iBGP works by exchanging routing information between two or more routers within an AS. Each router sends its own routing table to its neighbors, which contains information about the networks it knows and how they can be reached from that router. By default, iBGP neighbors only share BGP routes learned from eBGP neighbors, which are routers in different ASes. This is because iBGP assumes that all routers within an AS have consistent internal routing information provided by an IGP, such as OSPF or IS-IS. Therefore, iBGP neighbors do not need to share IP address information of loopbackinterfaces or directly connected interfaces, unless explicitly configured to do so by using commands such as neighbor update-source or network.
References: iBGP Ultimate Guide | How iBGP Is Different From eBGP, Ericsson IP Networking - Routing Protocols
NEW QUESTION # 27
What is the function of LSR from an LDP perspective?
- A. The LSR distributes labels of LDP to its FEC peers.
- B. The LSR distributes labels of FEC to its LDP peers.
- C. The LSR distributes packets of FEC to its LDP peers.
- D. The LSR distributes packets of LDP to its FEC peers.
Answer: B
Explanation:
Explanation
The function of LSR from an LDP perspective is to distribute labels of FEC to its LDP peers. LSR stands for Label Switching Router, which is a router that forwards packets based on labels rather than IP addresses in an MPLS network. LDP stands for Label Distribution Protocol, which is a protocol that distributes labels for MPLS forwarding along the shortest path calculated by an IGP. FEC stands for Forwarding Equivalence Class, which is a group of packets that are forwarded in the same manner by an LSR. An LSR uses LDP to advertise the label mappings for each FEC to its LDP peers, which are other LSRs that have established an LDP session with it12.
References: Ldp | Microsoft Learn, Label Distribution Protocol - Wikipedia
NEW QUESTION # 28
Review the exhibit.
Given the routing table shown in the exhibit, what is the next-hop to reach the host 192.168.1.129?
- A. 10.126.131.250
- B. 10.126.131.251
- C. 10.126.131.248
- D. 10.126.131.252
Answer: A
Explanation:
Explanation
The next-hop to reach the host 192.168.1.129 is 10.126.131.250. This can be determined by looking at the routing table in the exhibit. The host 192.168.1.129 falls within the range of the network 192.168.1.64/26, which has a next-hop of 10.126.131.250. References: Ericsson IP Networking - IP Addressing, Software Installation and Upgrade Overview (Junos OS)
NEW QUESTION # 29
Which action will influence BGP route selection within your AS?
- A. changing the default link metric
- B. changing the default value of the local preference
- C. reducing number of hops in the network
- D. changing the administrative distance for eBGP
Answer: B
Explanation:
Explanation
The action that will influence BGP route selection within your AS is changing the default value of the local preference attribute. The local preference attribute is used to indicate the preference of a path among multiple paths learned from different external BGP neighbors or autonomous systems (ASes). The higher the local preference value, the more preferred the path is within your AS, and vice versa. The default value of local preference is 100, but you can change it using route maps or other configuration methods on your BGP routers. References: Ericsson IP Networking - Routing Protocols, BGP Attributes and Path Selection, BGP Local Preference Attribute: Controlling Traffic Like a Pro
NEW QUESTION # 30
Within an IGP area, which two statements are correct? (Choose two.)
- A. Routers advertise information about themselves.
- B. Routers discard valid but inaccurate information from neighbors.
- C. Routers relay information delivered by neighbors.
- D. Routers summarize information they learn from neighbors.
Answer: A,C
Explanation:
Explanation
Within an IGP area, routers advertise information about themselves and relay information delivered by neighbors. This is how link-state routing protocols such as OSPF and IS-IS work. They flood information about the network topology to all routers in the same area or domain. That information is then used to build a complete network connectivity map and to calculate the shortest path to destinations. Routers do not summarize or discard information within an area, unless they are configured to do so by some filtering mechanism. References: Ericsson IP Networking - Routing Protocols, IP Routing: ISIS Configuration Guide - IS-IS Overview and Basic Configuration
NEW QUESTION # 31
IPv6 link-local addresses are designed to be used in which three situations? (Choose three.)
- A. for local IP communication on the IPv6 capable routers
- B. when routers are not present
- C. for neighbor discovery
- D. by routers to forward packets with link-local source addresses to other links
- E. addressing on a single link for purposes such as auto-address configuration
Answer: A,C,E
Explanation:
Explanation
IPv6 link-local addresses are designed to be used in three situations: for neighbor discovery, for local IP communication on the IPv6 capable routers, and for addressing on a single link for purposes such as auto-address configuration. Neighbor discovery is a protocol that allows IPv6 nodes to discover each other and learn their link-layer addresses on a local network. Neighbor discovery uses link-local addresses to send and receive messages such as router advertisements, router solicitations, neighbor advertisements, and neighbor solicitations34. Local IP communication on the IPv6 capable routers refers to the ability of routers to exchange routing information or management traffic using their link-local addresses as source and destination addresses. This reduces the need for global unicast addresses on router interfaces that are not reachable from outside the local network35. Addressing on a single link for purposes such as auto-address configuration refers to the use of link-local addresses to enable IPv6 nodes to obtain an address without manual configuration or a DHCP server. Link-local addresses can be automatically derived from the interface identifier in the modified EUI-64 format or randomly generated. Link-local addresses can also be used to test the connectivity of a link before obtaining a global unicast address36.
References: Understand the IPv6 Link-Local Address - Cisco, Link Local Address - GeeksforGeeks, IPv6 Address Types | Link-Local, Global Unicast, etc. IPCisco, MPLS Label Distribution Protocol Commands - Cisco
NEW QUESTION # 32
What is the CLI command to obtain the software version in Ericsson Router 6000 products?
- A. show version
- B. show release
- C. show log
- D. show sysstat
Answer: A
Explanation:
Explanation
The CLI command to obtain the software version in Ericsson Router 6000 products is show version. This command displays information about the software release, the hardware model, the serial number, the uptime, and the boot image of the router. References: [ERICSSON SMARTEDGE 600 HARDWARE MANUAL Pdf Download | ManualsLib], Ericsson Router 6000 Series - Ericsson
NEW QUESTION # 33
What are two roles of the DHCP protocol in a network? (Choose two.)
- A. It is used to inform hosts about the default gateway.
- B. It is used by hosts to obtain the IP address and other parameters from the DHCP server.
- C. It provides the authorization function to the network.
- D. It provides information about the number of hops between the source and the destination.
Answer: A,B
Explanation:
Explanation
Two roles of the DHCP protocol in a network are:
It is used by hosts to obtain the IP address and other parameters from the DHCP server. DHCP stands for Dynamic Host Configuration Protocol, which is a protocol that provides automatic and centralized management of IP addresses and other network configuration parameters for devices connected to a network. A host that needs an IP address can send a request to a DHCP server, which will assign an available IP address from a pool and lease it to the host for a certain period of time34.
It is used to inform hosts about the default gateway. The default gateway is the IP address of the router that connects the host to other networks. The default gateway is one of the parameters that can be delivered by the DHCP server to the host, along with other parameters such as subnet mask, DNS server, domain name, etc. The host can use the default gateway to send packets to destinations outside of its local network34.
References: What Is DHCP? (Dynamic Host Configuration Protocol) - Lifewire, Dynamic Host Configuration Protocol - Wikipedia
NEW QUESTION # 34
In an Ericsson Router 6000, which command is used to begin making changes to the router settings?
- A. configure
- B. capabilities
- C. commit
- D. set metric
Answer: A
Explanation:
Explanation
The command that is used to begin making changes to the router settings in an Ericsson Router 6000 is configure. This command enters the configuration mode, where various commands can be used to modify the router parameters, such as interfaces, protocols, services, security, etc. To exit the configuration mode, the command end can be used. To save the changes made in the configuration mode, the command commit can be used56.
References: Router 6000 Series - Ericsson, Ericsson Router 6000 series (6471/6672/6675) Commands for
2G/3G/4G/5G technologies... - YouTube
NEW QUESTION # 35
......
Maximum Grades By Making ready With ECP-206 Dumps: https://protechtraining.actualtestsit.com/Ericsson/ECP-206-exam-prep-dumps.html